Extreme Networks BlackDiamond 6800 MPLS Guide de l'utilisateur Page 103
- Page / 176
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MPLS Module Installation and User Guide 5-29
Configuration Example
The following commands configure two RSVP-TE LSPs; one is the primary and the
other is a secondary or backup LSP. Each LSP uses the same profile but different paths.
config mpls rsvp add lsp Glasgow-Birmingham-lsp path
Glasgow-Birmingham-pri-path Glasgow-Birmingham-pro primary
config mpls rsvp lsp Glasgow-Birmingham-lsp add path
Glasgow-Birmingham-sec-path Glasgow-Birmingham-pro secondary
The secondary LSP is signaled, however it remains in a standby state unless the
primary path becomes unavailable.
By default, a TLS tunnel flows over any available LSP. However, a TLS tunnel can be
specifically directed to use a configured RSVP-TE based LSP. Configuration is no
different from configuring an LDP-based TLS tunnel, except that the RSVP-TE LSP is
explicitly specified. The following command specifically directs the TLS tunnel to use a
previously configured RSVP-TE:
config mpls add tls-tunnel Glasgow-Birmingham-cust1 lsp
Glasgow-Birmingham-lsp oxford-university vcid 50 from 2.0.0.0
- MPLS Module Installation 1
- Contents 3
- 3 Configuring the MPLS Module 4
- 5 Configuring RSVP-TE 6
- 6 MPLS and IP Routing 7
- Index of Commands 10
- Introduction 11
- Conventions 12
- Related Publications 13
- Overview 15
- Summary of Features 16
- MPLS Module LED Indicators 18
- Service Port 19
- Console Port 19
- About BlackDiamond Modules 19
- About the MPLS Module 20
- About MPLS 20
- About MPLS Layer-2 VPNs 21
- About IP Unicast Forwarding 22
- Installing or Replacing an 25
- MPLS Module 25
- Safety Information 27
- MPLS Module Slot Locations 28
- Preparing for Installation 29
- (a) Loosen 31
- (b) Pivot 31
- LED Indicators 32
- Troubleshooting 33
- Table 2-1: MPLS Module LEDs 34
- Fixing Configuration Errors 35
- Fixing Power-Related Problems 36
- command to reload the image 37
- Tools and Equipment 38
- Removing an MPLS Module 38
- Configuring the MPLS Module 41
- MPLS Terms and Acronyms 42
- Overview of MPLS 43
- Label Switched Paths 44
- Label Retention Modes 45
- Label Switch Routers 46
- MPLS cloud 47
- MPLS Layer 48
- Label Stack Encoding 49
- Penultimate Hop Popping 50
- Label Binding 50
- Label Space Partitioning 50
- Configuring MPLS 52
- Configuring Interfaces 55
- You must maintain identical 56
- settings on all LERs in the 56
- Configuring QoS Mappings 57
- Dot1p-to-exp Mappings 58
- Exp-to-dot1p Mappings 58
- Protocol 63
- Advertising Labels 64
- Propagating Labels 64
- Configuring LDP 65
- Configuring LDP on a VLAN 68
- Configuring LDP Filters 68
- Restoring LDP Session Timers 71
- RSVP Elements 76
- Path Message 77
- Reservation Message 78
- Path Error Message 78
- Reservation Error Message 78
- Path Tear Message 78
- Reservation Styles 79
- Bandwidth Reservation 80
- Bandwidth Accounting 81
- RSVP State 81
- Traffic Engineering 82
- RSVP Objects 83
- RSVP Features 84
- Route Recording 85
- Explicit Route Path LSPs 85
- Redundant LSPs 86
- Improving LSP Scaling 87
- Configuring RSVP-TE on a VLAN 90
- Configuring an RSVP-TE Path 92
- Configuring an Explicit Route 93
- Configuring an RSVP-TE LSP 97
- Displaying the RSVP-TE LSP 99
- Configuration Example 100
- 172.25.23.32/30 101
- Primary LSP 101
- Secondary LSP 101
- Configuring RSVP-TE 102
- MPLS and IP Routing 105
- Routing Using LSPs 106
- 10.1.1.1/32 10.2.1.1 31 30 107
- 10.0.1.0/24 10.2.1.1 32 31 107
- 10.0.2.0/24 10.2.1.1 33 31 107
- 10.0.3.0/24 10.2.1.1 34 31 107
- Equal Cost LSPs 108
- LSPs and IBGP Next Hops 109
- Configuring MPLS Layer-2 VPNs 111
- Layer-2 VPN Services 112
- MPLS VC Tunnels 112
- Overview of MPLS Layer-2 VPNs 113
- Layer-2 VPN Domains 114
- MAC Learning 114
- TLS VPN Characteristics 115
- Adding a TLS Tunnel 118
- Deleting a TLS Tunnel 119
- 11.0.2.0/24 121
- 11.0.4.0/24 121
- TLS Tunnel 121
- Full Mesh TLS Configuration 122
- Using ESRP with MPLS TLS 127
- Tunnel Endpoint VLANs 128
- LSP Tracking 131
- Accounting 135
- Configuring Access Profiles 137
- Creating an Access Profile 139
- Specifying Subnet Masks 141
- Sequence Numbering 141
- Permit and Deny Entries 141
- Autonomous System Expressions 142
- Configuring Route Maps 143
- Creating a Route Map 145
- Route Map Operation 147
- Data traffic 148
- 192.168.101.0/24 148
- 192.168.102.0/24 148
- 192.168.100.0/24 148
- See the 153
- General Switch Attributes 156
- 802.1p and 802.1Q Commands 158
- VLAN Commands 159
- FDB Commands 159
- Basic IP Commands 159
- Optional 160
- Keywords 160
- ICMP Commands 161
- OSPF Commands 162
- BGP Commands 162
- Route Map Commands 162
- PPP Commands 163
- ESRP and VRRP Commands 163
- Debug Trace Commands 164
- • Quality of Service (QoS) 165
- Supported MIBs and Standards 167
- MIBs Supported for MPLS 168
- Numerics 169
Produits connexes et manuels pour Commutateurs de réseau Extreme Networks BlackDiamond 6800 MPLS
(29 pages)
© 2020, manymanuals.fr. Tous droits réservés | 2.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels